Evolution 80GX Specifications

Sukhoi SU-26MM SEAssembly Manual

10 Hangar 9 Sukhoi SU-26MM SE 2. Use a hobby knife with a #11 blade to remove the covering on the fuselage for the charge jacks on the right and le

11Hangar 9 Sukhoi SU-26MM SE 8. Connect the regulator to the receiver using a 12-inch (305mm) EC3 extension. Route the lead through the openings in

12 Hangar 9 Sukhoi SU-26MM SEImportant: The fuel vent line has been wrapped up and back around the tank to stop the fuel tank from siphoning fuel duri

13Hangar 9 Sukhoi SU-26MM SENote: It may be necessary to rotate the choke lever depending on how the choke will be operated. Make sure the position of

14 Hangar 9 Sukhoi SU-26MM SE 12. Secure the pushrod wire to the servo arm using a pushrod connector. Snap the connector on the pushrod wire to secu

15Hangar 9 Sukhoi SU-26MM SE 18. Use a hobby knife and #11 blade to remove the covering for the ignition switch. Mount the switch using the hardware

16 Hangar 9 Sukhoi SU-26MM SE 24. Mount the propeller and spinner on the engine. Make sure to balance the propeller to reduce any vibrations that may

17Hangar 9 Sukhoi SU-26MM SE 3. Attach the header to the engine using the hardware provided with the header or engine.Note: Before installing the tu

18 Hangar 9 Sukhoi SU-26MM SEEngine Installation (DA85)Required PartsFuselage assembly 90-degree snap link1/4-inch lock washer (4) 1/4-20 blind nut

19Hangar 9 Sukhoi SU-26MM SE 6. Attach the servo horn to the throttle servo. With the throttle servo and carburetor linkage in the closed position,

2 Hangar 9 Sukhoi SU-26MM SE WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure

20 Hangar 9 Sukhoi SU-26MM SE D. Use a hobby knife to trim the covering 1/8-inch (3mm) away from the edges of the opening. The excess material will

21Hangar 9 Sukhoi SU-26MM SENote: Always use threadlock on metal-to-metal fasteners. 2. Attach the rudder servo arm onto the rudder servo using a 2

22 Hangar 9 Sukhoi SU-26MM SE 3. Use the screws removed from the fuselage in Step 2 to secure the stabilizer to the fuselage.Note: A small of canop

23Hangar 9 Sukhoi SU-26MM SE 3. Use a 3/32-inch hex wrench and replace the 4-40 x 3/4-inch socket head screws securing the landing gear cover on the

24 Hangar 9 Sukhoi SU-26MM SE 4. Repeat Steps 1 though 3 to install the remaining wing panel. 5. Attach the canopy hatch to the fuselage using the

25Hangar 9 Sukhoi SU-26MM SEChecking the Control Linkages and Centering the Control SurfacesRequired PartsAssembled airframe TransmitterRequired Too

26 Hangar 9 Sukhoi SU-26MM SEAileron:High Rate:Up: 35/16-inches 84mm 35 degreesDown: 35/16-inches 84mm 35 degreesLow Rate:Up: 111/16-inches 43

27Hangar 9 Sukhoi SU-26MM SERange Test Your RadioBefore each flying session, and especially with a new model, it is important to perform a range check

28 Hangar 9 Sukhoi SU-26MM SEDAMAGE LIMITSHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

29Hangar 9 Sukhoi SU-26MM SEUNITED KINGDOMHorizon Hobby LimitedUnits 1-4 Ployters RdStaple TyeHarlow, EssexCM18 7NSUnited [email protected]

3Hangar 9 Sukhoi SU-26MM SEPACKAGED INDIVIDUALLYLeft wing with aileron 1Right wing with aileron 1Left stabilizer with elevator 1Right stabilizer wi

30 Hangar 9 Sukhoi SU-26MM SE (c) An area away from the safety line must be maintained for spectators. (d) Intentional flying behind the safety line

31Hangar 9 Sukhoi SU-26MM SEDA 85 Mounting Template

28055Printed 09/2010© 2010 Horizon Hobby, Inc.horizonhobby.com Hangar9.comFutaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Cor

4 Hangar 9 Sukhoi SU-26MM SE Safety Precautions and WarningsRead and follow all instructions and safety precautions before use. Improper use can resul

5Hangar 9 Sukhoi SU-26MM SESafe Operating Recommendations• Inspectyourmodelbeforeeveryflighttomakecertain it is airworthy.• Beawareofany

6 Hangar 9 Sukhoi SU-26MM SERequired AdhesivesThin CA (PAAPT08)Medium CA (PAAPT02)Threadlock (PAAPT42)5-minute Epoxy, 8 oz (PAAPT38)30-Minute Epox

7Hangar 9 Sukhoi SU-26MM SE 5. Use the hook and loop strap to secure the receiver in position. Make sure to use foam to isolate the receiver from th

8 Hangar 9 Sukhoi SU-26MM SEBattery and Regulator Installation - 3D FlightRequired PartsFuselage Hook and loop strap (2)12-inch EC3 extension (2) T

9Hangar 9 Sukhoi SU-26MM SENote: Use the 4-pin balance connection (THP4P10E) on the receiver Li-Po batteries to make it easier to connect the charger.